Details up front: 99.4% · dulaglutide · QYB.
This is a planning question. I know what my options are; I do not know how to weigh them.
What I want is the minimum viable version, which I suspect is smaller than what I would design.
What is the minimum version of this that is still defensible?
99.4 per cent purity with no content figure leaves the milligram number unmeasured. Purity says 99.4 of every 100 units of detected area is dulaglutide and 0.6 is something else. Content says how many milligrams are in the glass. The two do not constrain each other: a vial can be 99.4 per cent pure and still be under label, because water and counter-ion are part of the gross mass and neither shows up as an impurity peak. If you buy one test, buy the one that changes your arithmetic.
Concretely, identity and purity are orthogonal, and a high purity says almost nothing about whether the peak is actually what you think it is.
Gradient slope controls resolution, and gentler slopes resolve co-eluting impurities into separate peaks — so the better method reports the worse purity number.
| Δ mass (Da) | Most likely cause | Distinguishing feature |
|---|---|---|
| +1 | Deamidation (Asn or Gln) | New peak, slightly earlier retention |
| −17 | Loss of ammonia | Often with deamidation |
| −18 | Dehydration / succinimide | pH-dependent, reversible |
| +16 | Oxidation (Met, Trp) | Earlier retention, light-related |
| −128 | Missing Gln or Lys | Deletion sequence from synthesis |
| 0 | Isomer: racemisation or scrambling | Same mass, shifted retention |
Retention time is sequence-specific and method-specific, so comparing your result to a supplier value using a different method is meaningless without method documentation.
Inter-laboratory studies on identical peptide material routinely find half-a-per-cent to a full-per-cent spreads in reported purity on the same sample.
Worth noting that method standardisation is poor in the research-grade space compared to pharmaceutical work, so identical-looking methods can produce different results.
The practical summary: ask for the chromatogram and the method, and ignore the headline number until you have both.
HPLC purity, identity confirmation and quantified content on the vial you actually hold. Reports arrive with the chromatogram attached, not just a number.
Submit a sampleFounded 1998. ISO 9001 and cGMP certified, 1,500+ staff and 200+ patents. The synthesis house behind a great many of the vials that get sent out for testing - batch-specific documentation with every order.
Visit GL BiochemOn the detail: the single most important distinction is between what purity measures — the fraction of detected material that is your target — and what you actually want to know — how much of the material in the vial is your target.
Column pore size affects mass transfer — a 100 Angstrom packing on a 5 kDa peptide restricts diffusion, broadening the peak and potentially hiding small impurities in the shoulders.
It helps to be literal here: the fraction of your main peak that is actually your target versus isomers, fragments or related sequences is invisible without complementary identity testing.
The ICH Q3A impurity thresholds and the relevant pharmacopoeial chapters all specify method validation requirements that almost no research-grade certificate claims to meet.
Compare purity within a single laboratory on the same method, never across laboratories.
The method matters more than the vial, which is why specifying a method buys you far more than changing suppliers does.
Buffer versus acid in the mobile phase changes the ionisation state of basic and acidic residues, shifting retention and selectivity — same vial, potentially different separation.
Temperature affects the dynamics of molecular conformation, and if a peptide has proline residues that interconvert on the chromatographic timescale, the peak will split or shoulder at low temperature and collapse at high temperature.
The limitation is that single-digit micro-impurities become invisible at typical reporting thresholds, so "no impurities detected" means "none above one in two thousand."
If you are ranking vendors, specify a method and have all samples tested at the same place.
Read the chromatogram before you read the number, because the number without the trace is not a measurement, it is a claim.
Tailing factor measures peak shape, and a badly tailing peak spreads into the region where small impurities live, forcing tangent-skim integration that assigns tail area to the main peak.
I would be careful about over-reading a single measurement — treat it as a data point, not as ground truth.
If you only pay for one test, pay for quantified content. Purity is the number everyone quotes and content is the number that changes what you do.
edited 26 Jun 2025 by assay_blank — fixed an arithmetic slip in the third paragraph
Gradient slope is the most powerful parameter and almost nobody mentions it, which is why two reports on the same material disagree by a point.
Integration of the shoulder — whether you use perpendicular drop or tangent skim — determines what area gets assigned to the main peak versus the impurity table.
Published side-by-side method comparisons show that a two-point difference in purity on the same vial is easily explained by method choice alone.
In practice: ask for the chromatogram, check the method section, check the lot number against the vial, and set your accept threshold before you see the result rather than after.
Ask PeptideStack is a static archive. Posting is closed, but the norms are worth stating: answer the question that was asked, show your working, cite the trial or the certificate, and say plainly where the evidence runs out.