Details up front: a U-100 insulin syringe · 10 mg · 2 mg/mL.
This should be a straightforward calculation and I keep getting two different answers.
The numbers are arbitrary; the method is what I am after.
Can someone show the working rather than just the answer?
The underlying point is that work in the order concentration, then volume, then units, and the arithmetic stops being confusing. Concentration is milligrams per millilitre and comes from the vial contents and the diluent volume. Volume per dose is dose divided by concentration. Units on a U-100 syringe are volume in millilitres multiplied by one hundred.
The concentration you actually work with is label claim times content fraction divided by actual diluent volume, which is usually not the same as the nominal concentration because content is usually not 100 per cent and you rarely measure the diluent volume to 0.1 mL precision.
Do not use the same needle to pierce the stopper and to administer. The tip is blunted by the stopper, and the hub now contains a dose you are about to lose to dead space anyway.
The Arrhenius relationship for drawing kinetics means that cold solution takes noticeably longer to draw than room-temperature solution.
I would flag the obvious failure mode: people get the concentration right, get the volume right, and then read the syringe against the wrong scale.
Write the arithmetic on the vial label. It costs nothing and removes the step where you reconstruct it from memory.
edited 17 Jun 2025 by priya_menon — clarified the distinction between purity and content
Analytical standards and reagents with traceable certificates. Every quantitative result you read inherits the accuracy of the standard behind it.
Shop standardsThe part that matters: the single most useful thing to do is write the arithmetic on the vial label, because you will reconstruct it from memory at an inconvenient moment if you do not.
On filtration: a 0.22 µm syringe filter will remove particulates and organisms, and it will also adsorb a fraction of your peptide onto the membrane — with a low-binding PVDF or PES membrane the loss is typically a few per cent.
Worth being precise here: dead space quantified: a fixed-needle insulin syringe holds roughly 3 to 5 µL in the hub and needle after the plunger bottoms out. A luer-lock syringe with a detachable needle holds 35 to 100 µL depending on the hub design. At 5 mg/mL that is 15 to 25 µg lost per draw on the insulin syringe and 175 to 500 µg on the luer-lock — which over ten draws is the difference between losing a rounding error and losing half a milligram.
Published data on syringe dead space quantifies low-dead-space designs as retaining under 2 µL against 35 µL or more for conventional detachable-needle syringes.
The limitation is that technique reduces risk, it does not remove it, and nothing you can do outside a controlled environment makes a non-sterile preparation sterile.
Do the arithmetic twice, ideally with someone else doing it independently.
Write the units at every step, because units errors are the failure mode that catches everyone eventually.
Worked example, because the general form is easier to trust once you have seen it once. Take a 10 mg vial and add 2 mL of diluent: the concentration is 10 ÷ 2 = 5 mg/mL. A 0.5 mg dose is 0.5 ÷ 5 = 0.1 mL. On a U-100 syringe, where 1 unit = 0.01 mL, that is 0.1 ÷ 0.01 = 10 units. Change the diluent to 1 mL and the same dose becomes 5 units — same dose, half the resolution.
The relevant detail is that rotation of injection site is a tolerability measure, not a pharmacokinetic one, but if you are going to do it you might as well do it right.
The insulin-unit standard U-100 means 100 units per millilitre, so one unit is 0.01 mL — this is the conversion that trips up more people here than any other single piece of arithmetic.
If in doubt, use more diluent and accept the shorter usable window.
Ask PeptideStack is a static archive. Posting is closed, but the norms are worth stating: answer the question that was asked, show your working, cite the trial or the certificate, and say plainly where the evidence runs out.