What I have: 98.8% · dulaglutide.
I can do the algebra. I am not confident about the conversion factors.
If there is a standard way to lay this out, I would rather learn that than invent one.
Can someone walk through the arithmetic step by step?
98.8 per cent is at the top of what stepwise synthesis delivers on a chain this long, and it is reachable rather than fictional. Every coupling is high-yielding and none is quantitative, so the deletion and truncation sequences that survive purification are what occupies the remaining 1.2 per cent. Above roughly 98 per cent you are fighting the purification rather than the synthesis, which is why a 98.8 per cent figure on dulaglutide deserves a method question — column, gradient, wavelength — rather than either belief or dismissal.
It helps to be literal here: purity is a method-dependent figure, and that is not a limitation of the measurement, it is a property of what the measurement actually answers.
Retention time is sequence-specific and method-specific, so comparing your result to a supplier value using a different method is meaningless without method documentation.
In practice, column pore size affects mass transfer — a 100 Angstrom packing on a 5 kDa peptide restricts diffusion, broadening the peak and potentially hiding small impurities in the shoulders.
Inter-laboratory studies on identical peptide material routinely find half-a-per-cent to a full-per-cent spreads in reported purity on the same sample.
The caveat is that purity without identity is only half an answer — a high purity does not mean the peak is actually what you think it is.
The practical summary: ask for the chromatogram and the method, and ignore the headline number until you have both.
Analytical standards and reagents with traceable certificates. Every quantitative result you read inherits the accuracy of the standard behind it.
Shop standardsThe honest answer is that the achievable range of plausible purity figures for a given vial is wider than most people expect.
Mobile phase additive choice affects ionisation and peak shape — TFA gives sharp peaks but suppresses mass spectrometry signal, formic acid gives worse peaks but preserves signal.
It helps to be literal here: buffer versus acid in the mobile phase changes the ionisation state of basic and acidic residues, shifting retention and selectivity — same vial, potentially different separation.
The limitation is that single-digit micro-impurities become invisible at typical reporting thresholds, so "no impurities detected" means "none above one in two thousand."
If you are ranking vendors, specify a method and have all samples tested at the same place.
Start from what the detector sees, because that tells you what the number means.
Tailing factor measures peak shape, and a badly tailing peak spreads into the region where small impurities live, forcing tangent-skim integration that assigns tail area to the main peak.
Stated carefully, mass on column affects detector linearity and peak overlap — overloading broadens peaks and hides neighbours, while underloading improves resolution but loses sensitivity.
I would be careful about over-reading a single measurement — treat it as a data point, not as ground truth.
Compare purity within a single laboratory on the same method, never across laboratories.
More usefully, the method matters more than the vial, which is why specifying a method buys you far more than changing suppliers does.
The fraction of your main peak that is actually your target versus isomers, fragments or related sequences is invisible without complementary identity testing.
One qualification: achieving purity above roughly 98 per cent on a 30-residue peptide is fighting the chemistry of synthesis, not the quality of the purification.
If you only pay for one test, pay for quantified content. Purity is the number everyone quotes and content is the number that changes what you do.
Read the chromatogram before you read the number, because the number without the trace is not a measurement, it is a claim.
Temperature affects the dynamics of molecular conformation, and if a peptide has proline residues that interconvert on the chromatographic timescale, the peak will split or shoulder at low temperature and collapse at high temperature.
Published side-by-side method comparisons show that a two-point difference in purity on the same vial is easily explained by method choice alone.
In practice: ask for the chromatogram, check the method section, check the lot number against the vial, and set your accept threshold before you see the result rather than after.
Ask PeptideStack is a static archive. Posting is closed, but the norms are worth stating: answer the question that was asked, show your working, cite the trial or the certificate, and say plainly where the evidence runs out.