What is the arithmetic to convert 4 mg in 2 mL into units on a U-100 scale?

For reference: 4 mg · 2 mL.

I would rather understand the derivation than memorise the outcome.

Two people I asked gave two answers that differ by a factor of ten, which is suggestive.

Can someone show the working rather than just the answer?

Put another way, work in the order concentration, then volume, then units, and the arithmetic stops being confusing. Concentration is milligrams per millilitre and comes from the vial contents and the diluent volume. Volume per dose is dose divided by concentration. Units on a U-100 syringe are volume in millilitres multiplied by one hundred.

Rotation of injection site is a tolerability measure, not a pharmacokinetic one, but if you are going to do it you might as well do it right.

Stated carefully, number of stopper piercings matters less than the gauge doing the piercing. A 30G or 31G needle through a butyl stopper leaves a track that reseals; a 21G or 18G drawing needle punches a core and can drop it into the solution.

The caveat is that this assumes the vial contains what the label says, and if the content assay has not been done, the arithmetic is precise about an unknown quantity.

If in doubt, use more diluent and accept the shorter usable window.

To be exact about it, this is arithmetic, so let us do the arithmetic rather than argue about it.

Air bubbles at these volumes are a measurement problem rather than a safety one. A 2 mm bubble in a 0.3 mL syringe is roughly 4 µL, which at 10 units drawn is a four per cent error.

Put another way, breaking it down further: if a 10 mg vial has 96.5 per cent content, you have 9.65 mg of peptide. Divide that by 2.00 mL and your concentration is 4.825 mg/mL, not 5.00 mg/mL, which is a 3.5 per cent systematic error in every dose calculation.

Worth noting: the concentration after reconstitution is not the same as the label claim, and most people do not account for the difference.

Do the arithmetic twice, ideally with someone else doing it independently.

edited 5 Feb 2026 by w_okoye — added a caveat about sampling

The underlying point is that dose arithmetic has three parts: concentration from vial content and diluent, volume from dose and concentration, and units from volume and syringe scale.

The concentration you actually work with is label claim times content fraction divided by actual diluent volume, which is usually not the same as the nominal concentration because content is usually not 100 per cent and you rarely measure the diluent volume to 0.1 mL precision.

Dead space quantified: a fixed-needle insulin syringe holds roughly 3 to 5 µL in the hub and needle after the plunger bottoms out. A luer-lock syringe with a detachable needle holds 35 to 100 µL depending on the hub design. At 5 mg/mL that is 15 to 25 µg lost per draw on the insulin syringe and 175 to 500 µg on the luer-lock — which over ten draws is the difference between losing a rounding error and losing half a milligram.

The Arrhenius relationship for drawing kinetics means that cold solution takes noticeably longer to draw than room-temperature solution.

One qualification: if your arithmetic and someone else's disagree by a factor of ten, one of you has made a unit error, and writing out the units at every step is the diagnostic.

Write the arithmetic on the vial label. It costs nothing and removes the step where you reconstruct it from memory.

To be exact about it, write the units at every step, because units errors are the failure mode that catches everyone eventually.

On filtration: a 0.22 µm syringe filter will remove particulates and organisms, and it will also adsorb a fraction of your peptide onto the membrane — with a low-binding PVDF or PES membrane the loss is typically a few per cent.

The limitation is that technique reduces risk, it does not remove it, and nothing you can do outside a controlled environment makes a non-sterile preparation sterile.

If in doubt, use more diluent and accept the shorter usable window.

Mechanically, rounding to the nearest whole syringe unit is usually the right error to make, but understanding which direction it is and why matters.

Room temperature before drawing is worth the ten minutes. Cold solution is more viscous, draws slower, and condensation on a cold barrel makes it harder to read the meniscus.

The content assay results from major testing services show that nominal vial claim and measured content differ by one to ten per cent, making content a driver of dose error.

Do the arithmetic twice, ideally with someone else doing it independently.