Numbers first: cagrilintide · 10 mg/mL.
I would rather over-plan the first cycle and simplify later.
I am prepared to do the work if someone can tell me which work matters.
What does a sensible plan look like, and what are the decision points?
At 10 mg/mL a 0.25 mg dose is 2.5 units on a U-100 barrel and a 1 mg dose is 10 units. Volume is dose divided by concentration and one unit is 0.01 mL, so the unit count is dose ÷ 10 × 100. That puts the smaller dose below five units, where a half-graduation misread is more than ten per cent of the dose — reconstitute to a lower concentration if small doses are the point.
Answer first: diluent volume sets concentration and therefore resolution on the syringe barrel, and resolution is free at reconstitution and impossible to recover afterwards.
Content matters. If the same 10 mg vial assays at 94 per cent content, you have 9.4 mg. In 2 mL that is 4.7 mg/mL, and a nominal 0.5 mg draw of 10 units actually delivers 0.47 mg — a six per cent shortfall that no amount of careful drawing will fix.
| Vial | Diluent | Concentration | 0.25 mg | 0.5 mg | 1 mg | 2.5 mg |
|---|---|---|---|---|---|---|
| 5 mg | 1 mL | 5 mg/mL | 5 u | 10 u | 20 u | 50 u |
| 5 mg | 2 mL | 2.5 mg/mL | 10 u | 20 u | 40 u | 100 u |
| 10 mg | 1 mL | 10 mg/mL | 2.5 u | 5 u | 10 u | 25 u |
| 10 mg | 2 mL | 5 mg/mL | 5 u | 10 u | 20 u | 50 u |
| 10 mg | 3 mL | 3.33 mg/mL | 7.5 u | 15 u | 30 u | 75 u |
Units are U-100 insulin units, where 1 unit = 0.01 mL. Divide dose by concentration for millilitres, then multiply by 100.
Vial headspace is the hard constraint. A nominal 2 mL vial typically holds a little over 2 mL to the shoulder; adding 3 mL is not an option and attempting it wastes the lot.
Published content assay results across the independent testing services show nominal and measured content differing by one to ten per cent, which makes content the dominant term in dose error.
Check the vial can physically hold the volume before you draw it up.
Aggregated, published test results and vendor ratings built from submitted batches. Methodology stated, dataset browsable, no listing fees.
Browse resultsThe short version: more diluent means a lower concentration, a larger volume per dose and a finer reading; less means the opposite.
Worked example. A 10 mg vial reconstituted with 2 mL gives 5 mg/mL. A 0.5 mg dose is 0.5 ÷ 5 = 0.1 mL, which on a U-100 syringe is 10 units. Reconstitute the same vial with 1 mL and the concentration doubles to 10 mg/mL, the same dose becomes 0.05 mL, and you are now reading 5 units instead of 10 — the same dose at half the resolution.
Dead-space loss scales with the number of draws, not with the concentration, so a lower concentration spread over more draws loses proportionally less of the total peptide.
Insulin syringe barrel graduations are typically 1 unit on a 0.3 mL barrel, 1 unit on a 0.5 mL barrel and 2 units on a 1 mL barrel, which is why the barrel size changes what is readable.
Write the concentration on the label at reconstitution, in units per dose.
Start from the dose you intend to draw and work backwards to the volume that puts it in a readable part of the barrel.
Write the concentration and the resulting units-per-dose on the vial label at reconstitution. The arithmetic that is obvious now will not be obvious at six in the morning three weeks from now.
Round to a diluent volume you can measure accurately. Measuring 1.00 mL on a 1 mL syringe is reliable; measuring 1.37 mL on anything is not, and the error propagates into every dose.
U-100 means 100 units per millilitre by definition, so 1 unit is 0.01 mL and volume in millilitres times one hundred gives units. Every conversion here reduces to that.
Choose the volume that puts your largest intended dose between 10 and 30 units. Everything else follows.
The relevant detail is that this is the one decision in the whole preparation sequence that cannot be revised later, which is why it is worth thirty seconds of arithmetic.
For a dose that will change during titration, choose the volume for the largest intended dose rather than the first, so the whole schedule fits on one barrel without a mid-vial recalculation.
Nominal vial volumes in the standard 2R and 3R glass sizes have published brimful capacities well above the nominal fill, but the usable volume is bounded by the stopper displacement.
Concentration equals content over volume, and content is not label claim.
Aim for a dose volume somewhere between about 10 and 30 units on a U-100 barrel and the reading problem disappears.
The other direction: 10 mg in 3 mL is 3.33 mg/mL, and a 0.5 mg dose becomes 0.15 mL, or 15 units. More barrel, easier reading, and a larger fraction of the vial volume lost to dead space across the same number of draws.
A concentration calculated to three decimal places from a diluent volume measured to one is false precision.
Measure a volume you can actually measure. Round numbers, real syringes.
Ask PeptideStack is a static archive. Posting is closed, but the norms are worth stating: answer the question that was asked, show your working, cite the trial or the certificate, and say plainly where the evidence runs out.