How many units on a 1 mL luer-lock syringe is a 5 mg dose at 8 mg/mL?

The specifics, since they change the answer: a 1 mL luer-lock syringe · 5 mg · 8 mg/mL.

I would rather understand the derivation than memorise the outcome.

Two people I asked gave two answers that differ by a factor of ten, which is suggestive.

Can someone show the working rather than just the answer?

Work in the order concentration, then volume, then units, and the arithmetic stops being confusing. Concentration is milligrams per millilitre and comes from the vial contents and the diluent volume. Volume per dose is dose divided by concentration. Units on a U-100 syringe are volume in millilitres multiplied by one hundred.

The concentration you actually work with is label claim times content fraction divided by actual diluent volume, which is usually not the same as the nominal concentration because content is usually not 100 per cent and you rarely measure the diluent volume to 0.1 mL precision.

The part that matters: dead space quantified: a fixed-needle insulin syringe holds roughly 3 to 5 µL in the hub and needle after the plunger bottoms out. A luer-lock syringe with a detachable needle holds 35 to 100 µL depending on the hub design. At 5 mg/mL that is 15 to 25 µg lost per draw on the insulin syringe and 175 to 500 µg on the luer-lock — which over ten draws is the difference between losing a rounding error and losing half a milligram.

The caveat is that this assumes the vial contains what the label says, and if the content assay has not been done, the arithmetic is precise about an unknown quantity.

Write the arithmetic on the vial label. It costs nothing and removes the step where you reconstruct it from memory.

The part that matters: this is arithmetic, so let us do the arithmetic rather than argue about it.

Worked example, because the general form is easier to trust once you have seen it once. Take a 10 mg vial and add 2 mL of diluent: the concentration is 10 ÷ 2 = 5 mg/mL. A 0.5 mg dose is 0.5 ÷ 5 = 0.1 mL. On a U-100 syringe, where 1 unit = 0.01 mL, that is 0.1 ÷ 0.01 = 10 units. Change the diluent to 1 mL and the same dose becomes 5 units — same dose, half the resolution.

The underlying point is that breaking it down further: if a 10 mg vial has 96.5 per cent content, you have 9.65 mg of peptide. Divide that by 2.00 mL and your concentration is 4.825 mg/mL, not 5.00 mg/mL, which is a 3.5 per cent systematic error in every dose calculation.

The Arrhenius relationship for drawing kinetics means that cold solution takes noticeably longer to draw than room-temperature solution.

If in doubt, use more diluent and accept the shorter usable window.

edited 31 Jul 2024 by yuki_morishita — added a caveat about sampling

Specifically, the common error is getting the concentration right but then misreading the syringe scale, which is why checking the barrel marking rather than your memory matters.

Rotation of injection site is a tolerability measure, not a pharmacokinetic one, but if you are going to do it you might as well do it right.

On filtration: a 0.22 µm syringe filter will remove particulates and organisms, and it will also adsorb a fraction of your peptide onto the membrane — with a low-binding PVDF or PES membrane the loss is typically a few per cent.

The content assay results from major testing services show that nominal vial claim and measured content differ by one to ten per cent, making content a driver of dose error.

Worth noting: the concentration after reconstitution is not the same as the label claim, and most people do not account for the difference.

Do the arithmetic twice, ideally with someone else doing it independently.

The part that matters: the distinction that resolves most of these questions is understanding what concentration actually means and why it is not the same as label claim.

Air bubbles at these volumes are a measurement problem rather than a safety one. A 2 mm bubble in a 0.3 mL syringe is roughly 4 µL, which at 10 units drawn is a four per cent error.

The insulin-unit standard U-100 means 100 units per millilitre, so one unit is 0.01 mL — this is the conversion that trips up more people here than any other single piece of arithmetic.

One qualification: if your arithmetic and someone else's disagree by a factor of ten, one of you has made a unit error, and writing out the units at every step is the diagnostic.

Write the arithmetic on the vial label. It costs nothing and removes the step where you reconstruct it from memory.

The underlying point is that dose arithmetic has three parts: concentration from vial content and diluent, volume from dose and concentration, and units from volume and syringe scale.

Do not use the same needle to pierce the stopper and to administer. The tip is blunted by the stopper, and the hub now contains a dose you are about to lose to dead space anyway.

Published data on syringe dead space quantifies low-dead-space designs as retaining under 2 µL against 35 µL or more for conventional detachable-needle syringes.

The limitation is that technique reduces risk, it does not remove it, and nothing you can do outside a controlled environment makes a non-sterile preparation sterile.

If in doubt, use more diluent and accept the shorter usable window.