For reference: 98.4% · PeptideMeter · 98.2%.
Something has gone wrong and I would like to know how badly before I decide what to do.
Nothing else in the setup changed, which is what makes this puzzling.
What would you check first, and what would you conclude from each outcome?
Start from what the detector sees, because that tells you what the number means.
The fraction of your main peak that is actually your target versus isomers, fragments or related sequences is invisible without complementary identity testing.
| Δ mass (Da) | Most likely cause | Distinguishing feature |
|---|---|---|
| +1 | Deamidation (Asn or Gln) | New peak, slightly earlier retention |
| −17 | Loss of ammonia | Often with deamidation |
| −18 | Dehydration / succinimide | pH-dependent, reversible |
| +16 | Oxidation (Met, Trp) | Earlier retention, light-related |
| −128 | Missing Gln or Lys | Deletion sequence from synthesis |
| 0 | Isomer: racemisation or scrambling | Same mass, shifted retention |
In practice, tailing factor measures peak shape, and a badly tailing peak spreads into the region where small impurities live, forcing tangent-skim integration that assigns tail area to the main peak.
Inter-laboratory studies on identical peptide material routinely find half-a-per-cent to a full-per-cent spreads in reported purity on the same sample.
The practical summary: ask for the chromatogram and the method, and ignore the headline number until you have both.
Aggregated, published test results and vendor ratings built from submitted batches. Methodology stated, dataset browsable, no listing fees.
Browse resultsTo be exact about it, area percentage is not mass percentage, and conflating the two is the most common misreading of a purity figure.
Mobile phase additive choice affects ionisation and peak shape — TFA gives sharp peaks but suppresses mass spectrometry signal, formic acid gives worse peaks but preserves signal.
Buffer versus acid in the mobile phase changes the ionisation state of basic and acidic residues, shifting retention and selectivity — same vial, potentially different separation.
Published side-by-side method comparisons show that a two-point difference in purity on the same vial is easily explained by method choice alone.
If you are ranking vendors, specify a method and have all samples tested at the same place.
edited 6 Feb 2026 by tandem_gradient — added the method parameters
Concretely, the honest answer is that the achievable range of plausible purity figures for a given vial is wider than most people expect.
Gradient slope controls resolution, and gentler slopes resolve co-eluting impurities into separate peaks — so the better method reports the worse purity number.
The part that matters: temperature affects the dynamics of molecular conformation, and if a peptide has proline residues that interconvert on the chromatographic timescale, the peak will split or shoulder at low temperature and collapse at high temperature.
Proline conformer interconversion kinetics are well-characterised and the half-life is of the same order as the chromatographic peak width at room temperature.
Compare purity within a single laboratory on the same method, never across laboratories.
The single most important distinction is between what purity measures — the fraction of detected material that is your target — and what you actually want to know — how much of the material in the vial is your target.
Sample solvent strength affects peak shape — if you inject in strong solvent on a gradient starting in weak solvent, the solvent peak can distort your main peak or create a false shoulder.
Worth noting that method standardisation is poor in the research-grade space compared to pharmaceutical work, so identical-looking methods can produce different results.
The practical summary: ask for the chromatogram and the method, and ignore the headline number until you have both.
Read the chromatogram before you read the number, because the number without the trace is not a measurement, it is a claim.
Column pore size affects mass transfer — a 100 Angstrom packing on a 5 kDa peptide restricts diffusion, broadening the peak and potentially hiding small impurities in the shoulders.
One qualification: achieving purity above roughly 98 per cent on a 30-residue peptide is fighting the chemistry of synthesis, not the quality of the purification.
If you are ranking vendors, specify a method and have all samples tested at the same place.
edited 8 Jan 2026 by lyoph_cake — corrected a unit error in the worked example
Ask PeptideStack is a static archive. Posting is closed, but the norms are worth stating: answer the question that was asked, show your working, cite the trial or the certificate, and say plainly where the evidence runs out.