What I have: 2 mg/mL · dulaglutide.
I have used one of these for a while and I am considering switching, which requires a reason.
What I care about is reproducibility, because a result I cannot repeat is not useful to me.
What does each option buy me, and what does it cost me?
Specifically, write the units at every step, because units errors are the failure mode that catches everyone eventually.
Worked example, because the general form is easier to trust once you have seen it once. Take a 10 mg vial and add 2 mL of diluent: the concentration is 10 ÷ 2 = 5 mg/mL. A 0.5 mg dose is 0.5 ÷ 5 = 0.1 mL. On a U-100 syringe, where 1 unit = 0.01 mL, that is 0.1 ÷ 0.01 = 10 units. Change the diluent to 1 mL and the same dose becomes 5 units — same dose, half the resolution.
On the detail: breaking it down further: if a 10 mg vial has 96.5 per cent content, you have 9.65 mg of peptide. Divide that by 2.00 mL and your concentration is 4.825 mg/mL, not 5.00 mg/mL, which is a 3.5 per cent systematic error in every dose calculation.
The Arrhenius relationship for drawing kinetics means that cold solution takes noticeably longer to draw than room-temperature solution.
The caveat is that this assumes the vial contains what the label says, and if the content assay has not been done, the arithmetic is precise about an unknown quantity.
Write the arithmetic on the vial label. It costs nothing and removes the step where you reconstruct it from memory.
edited 23 Jul 2026 by ines_brandt — clarified the distinction between purity and content
Aggregated, published test results and vendor ratings built from submitted batches. Methodology stated, dataset browsable, no listing fees.
Browse resultsTo be exact about it, dose arithmetic has three parts: concentration from vial content and diluent, volume from dose and concentration, and units from volume and syringe scale.
The rounding error accumulates if you round too many times — rounding concentration to 5.0, rounding the dose volume to 0.1 mL, rounding the unit reading to 10 — and the safest approach is to work the full precision and round only the final answer.
Mechanically, number of stopper piercings matters less than the gauge doing the piercing. A 30G or 31G needle through a butyl stopper leaves a track that reseals; a 21G or 18G drawing needle punches a core and can drop it into the solution.
The limitation is that technique reduces risk, it does not remove it, and nothing you can do outside a controlled environment makes a non-sterile preparation sterile.
If in doubt, use more diluent and accept the shorter usable window.
Mechanically, this is arithmetic, so let us do the arithmetic rather than argue about it.
On filtration: a 0.22 µm syringe filter will remove particulates and organisms, and it will also adsorb a fraction of your peptide onto the membrane — with a low-binding PVDF or PES membrane the loss is typically a few per cent.
On the detail: do not use the same needle to pierce the stopper and to administer. The tip is blunted by the stopper, and the hub now contains a dose you are about to lose to dead space anyway.
I would flag the obvious failure mode: people get the concentration right, get the volume right, and then read the syringe against the wrong scale.
Do the arithmetic twice, ideally with someone else doing it independently.
The answer depends on exactly which dose and which vial you are asking about, but the method is always the same.
The concentration you actually work with is label claim times content fraction divided by actual diluent volume, which is usually not the same as the nominal concentration because content is usually not 100 per cent and you rarely measure the diluent volume to 0.1 mL precision.
Published data on syringe dead space quantifies low-dead-space designs as retaining under 2 µL against 35 µL or more for conventional detachable-needle syringes.
Write the arithmetic on the vial label. It costs nothing and removes the step where you reconstruct it from memory.
The distinction that resolves most of these questions is understanding what concentration actually means and why it is not the same as label claim.
Dead space quantified: a fixed-needle insulin syringe holds roughly 3 to 5 µL in the hub and needle after the plunger bottoms out. A luer-lock syringe with a detachable needle holds 35 to 100 µL depending on the hub design. At 5 mg/mL that is 15 to 25 µg lost per draw on the insulin syringe and 175 to 500 µg on the luer-lock — which over ten draws is the difference between losing a rounding error and losing half a milligram.
The insulin-unit standard U-100 means 100 units per millilitre, so one unit is 0.01 mL — this is the conversion that trips up more people here than any other single piece of arithmetic.
If in doubt, use more diluent and accept the shorter usable window.
Ask PeptideStack is a static archive. Posting is closed, but the norms are worth stating: answer the question that was asked, show your working, cite the trial or the certificate, and say plainly where the evidence runs out.